PET/杜邦美国/FR530食品级

[华韵塑胶PET防火阻燃V0]美国杜邦408 NC010 PET强高抗冲击性，刚度好;用于汽运;外壳结构件
[华韵塑胶PET防火阻燃V0]美国杜邦415HP BK503 PET耐蠕变性良好，优良尺寸稳定性 适用 汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦415HP NC010 PET高流动性，耐冲击性好，刚度好 用于 电气/电子应用;外壳
[华韵塑胶PET防火阻燃V0]美国杜邦530 BK503 PET优良的抗疲劳性，电气性能良好 适用汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦530 NC010 PET优良的抗疲劳性，电气性能良好 用于汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦530HTE NC010 PET通用性
[华韵塑胶PET防火阻燃V0]美国杜邦540SUV BK544 PET通用性
[华韵塑胶PET防火阻燃V0]美国杜邦545 BK504 PET耐蠕变性良好，优良尺寸稳定性;适用 汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦545 NC010 PET抗蠕变性良好，尺寸稳定性好;用于汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦815ER NC010 PET高流动性，耐强冲击性，刚度好 用于 电气/电子应用;外壳;薄零件
[华韵塑胶PET防火阻燃V0]美国杜邦830ER BK503 PET优良的抗疲劳性，良好的电气性能 适用 汽运;电子零件;电气适用
[华韵塑胶PET防火阻燃V0]美国杜邦935 BK505 PET良好的尺寸稳定性，电气性能良好 用于 汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦935 NC010 PET尺寸稳定性良好，高电气性能 适用汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦935SUV BK593 PET通用性
[华韵塑胶PET防火阻燃V0]美国杜邦940 BK505 PET高尺寸稳定性，良好的电气性能 适用汽车应用;电气/电子应用
[华韵塑胶PET防火阻燃V0]美国杜邦FR515 BK507 PET阻燃级;高尺寸稳定性， 用于 家电，电子零件;电气应用
[华韵塑胶PET防火阻燃V0]美国杜邦FR515 NC010 PET防火;良好的尺寸稳定性， 适用 家电，电子零件;电气运用

PET优点

编辑

1.有良好的力学性能，冲击强度是其他薄膜的3~5倍，耐折性好。

2.耐油、耐脂肪、耐稀酸、稀碱，耐大多数溶剂。

3.可在55-60℃温度范围内长期使用，短期使用可耐65℃高温，可耐-70℃低温，且高、低温时对其机械性能影响很小。

4.气体和水蒸气渗透率低，既有优良的阻气、水、油及异味性能。

5.透明度高，可阻挡紫外线，光泽性好。

6.无毒、无味，卫生安全性好，可直接用于食品包装。

Pet performance editor PET is an opalescent or light yellow highly crystalline polymer with a smooth, glossy surface. Creep resistance, fatigue resistance, wear resistance and dimensional stability, small wear and high hardness, with the greatest toughness in the Thermoplastic: good electrical insulation, less affected by temperature, but poor corona resistance. Non-toxic, weather resistance, anti-chemical stability, low water absorption, resistance to weak acid and organic solvents, but not resistant to hot water immersion, not resistant to Alkali. Pet Resin has high glass transition temperature, slow crystallization rate, long molding cycle, long molding cycle, large shrinkage, poor dimensional stability, brittle molding, low heat resistance and so on. With the improvement of nucleating agent, crystallizer and glass fiber reinforcement, PET has the following characteristics in addition to its PBT properties. 1. The thermal deformation temperature and long-term service temperature are the highest in thermoplastics. Because of its high heat resistance, the reinforced PET is impregnated for 10S in the solder bath at 250 °C, and is hardly deformed or discolored. 3. Bending strength 200MPA, elastic modulus 4000MPA, creep and fatigue resistance is also good, high surface hardness, mechanical properties and thermosetting polymer. 4. Pet Resin and reinforced PET are the lowest price in engineering plastics due to the fact that the ethylene glycol used to produce PET is almost half cheaper than the butanediol used to produce PBT. In order to improve the properties of PET, PET can be alloyed with PC, elastomer, PBT, PS, ABS and PA..