长春斯米克L323银焊条多少钱-焊材网供应信息-焊材网

商品详情

长春斯米克L323银焊条多少钱焊条就是涂有药皮的供焊条电弧焊使用的熔化电极，它是由药皮和焊芯两部分组成的。在焊条前端药皮有45°左右的倒角，这是为了便于引弧。在尾部有一段裸焊芯，约占焊条总长1/16，便于焊钳夹持并有利于导电。焊条的直径实际上是指焊芯直径）通常为2、2.5、3.2或3、4、5或6mm等几种规格，最常用的是小3.2、小4、小5三种，其长度“l”一般在200～550 mm之间。（1）药皮类型：不属已规定的类型电源种类：不规定主要特点：在某些焊条中采用氧化锆、金红石碱性型等，这些新渣系目前尚未形成系列

长春斯米克L323银焊条多少钱

（6）药皮类型：纤维素型电源种类：直流或交流主要特点：药皮中含15%以上的有机物，30%左右的氧化钛，焊接工艺性能良好，电弧稳定，电弧吹力大，熔深大，熔渣少，脱渣容易。可作立向下焊、深熔焊或单面焊双面成形焊接。立、仰焊工艺性好。适用于薄板结构、油箱管道、车辆壳体等焊接。随药皮中稳弧剂、黏结剂含量变化，分为高纤维素钠型（采用直流反接）、高纤维素钾型两类

Category 类别	Trade-mark 牌号	Specification 规格	Melting Point 熔点(℃)	Chemical comPOSTTTION 主要成份(%)	Application 用途	Equivalent to AWS 相当AWS
Copper zinc 铜锌	L103	Wire & rod 丝	885-888	Cu54 Zn Rem.	Brazing of copper, bronze and steel, subjected to low load. 钎焊铜、青铜和钢等受力不大工件	长春斯米克L323银焊条多少钱
Copper zinc 铜锌	L104	Foil 箔	890-930	Cu57 Mn2 Co2 Zn Rem.	Brazing of carbide cutting tool. 钎焊硬质合金刀具	（4）药皮类型：氧化铁型 ‖药皮主要成分：多量氧化铁及较多的锰铁脱氧剂 ‖焊接电源：直流或交流
Copper phosphorus 铜磷	L201	Cast rod, wire & rod, powder 铸条、丝、粉	710-800	P7 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-2
	L204	Cast rod, wire 铸条、丝	640-815	P5 Ag15 Cu Rem.	Brazing of copper, copper alloys, silver and molybdenum etc. 钎焊铜及铜合金、银、钼等金属。	BCuP-5
	L205	Cast rod, wire & rod, powder 铸条、丝、箔	640-800	P6 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-3
	L207	Cast rod, wire & rod 铸条、丝	640-770	P7 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-7
	L209	Cast rod, wire 铸条、丝	684-710	P7 Ag2 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金。	BCuP-6
Silver base 银基	L302	Wire & rod 丝	745-775	Ag25 Cu40 Zn Rem.	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L303	Wire & rod 丝	660-725	Ag45 Cu30 Zn余	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-5
	L303F	Flux coated rod 涂药丝	660-725	Ag45 Cu30 Zn Rem.	L303 coated with flux, the same application as L303. 外涂钎剂的L303，用途与L303相同	BAg-5
	L304	Foil 箔	690-775	Ag50 Cu34 Zn Rem.	Brazing of copper, copper alloys and steel etc. 钎焊铜及铜合金、钢等	BAg-6
	L308	Wire & rod 丝	779-780	Ag72 Cu Rem.	Brazing of copper and nickel under vacuum or reducing protective atmosphere. 铜和镍的真空或还原保护气氛钎焊	BAg-8
	L312	Wire & rod 丝	595-605		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L313	Wire & rod 丝	625-635		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-1a
	L321	Wire & rod 丝	615-650		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-7
	L323	Wire & rod 丝	665-755		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	（3）药皮类型：钛钙型电源种类：直流或交流主要特点：药皮中含氧化钛30%以上，钙、镁的碳酸盐20%以下，焊条工艺性能良好，熔渣流动性好，熔深一般，电弧稳定，焊缝美观，脱渣方便，适用于全位置焊接，如j422即属此类型，是目前碳钢焊条中使用最广泛的一种焊条。
	L325	Wire & rod 丝	645-685		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-36
	L326	Wire & rod 丝	650-720		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-34
Aluminum base 铝基	L400	Cast rod, wire & rod 铸条、丝	577-582	Si11.5 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊	BAlSi-4
Aluminum base 铝基	L401	Cast rod 铸条	525-535	Si5 Cu28 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊
Tin lead 锡铅	L600	Wire & rod 丝	183-185	Sn60 Sb≤0.8 Pb Rem.	Soldering of fusible metals and heat-treated part. 易熔金属及热处理件的钎焊	60Sn
	L601	Wire & rod 丝	183-227	Sn18 Sb2 Pb Rem.	Soldering of copper, copper alloys and galvanized iron plain sheet. 铜及铜合金、镀锌铁皮的钎焊。	18Sn
	L602	Wire & rod 丝	183-256	Sn30 Sb2 Pb Rem.	Soldering of copper, brass, copper alloys and galvanized iron plain sheet. 铜、黄铜、铁、镀锌铁皮的钎焊	30Sn
	L603	Wire & rod 丝	183-235	Sn40 Sb2 Pb Rem.	Soldering of copper, copper alloys, steel and zinc parts. 铜及铜合金、钢、锌制零件的钎焊	40Sn
	L604	Wire & rod 丝	183-222	Sn90 Sb≤0.15 Pb Rem.	Soldering of copper and steel for food and medicine field. 食品、医疗所需铜、钢等金属的钎焊	90Sn
	L605	Wire & rod 丝	232-240	Ag5 Sn95	Soldering of copper and steel for electrical and food field. 电器、食品所需铜、钢等金属的钎焊	(3)熔渣的比重应小于熔化金属的比重，凝固温度也应稍低于金属凝固温度，渣壳应易脱掉；
	L608	Wire & rod 丝	295-305	Sn5.5 Ag2.5 Pb Rem.	Soldering of copper, copper alloys, steel and stainless steel. 铜及铜合金、钢及不锈钢的钎焊
Nickel base 镍基	L702	Powder 粉	970-1000	Cr7 B3 Si4 Ni Rem.	Brazing of stainless steel under vacuum or protective atmosphere. 不锈钢真空或保护气氛钎焊	BNi-2