商铺名称：午虎特种合金（上海）有限公司
联系人：蔡玉兰（小姐）
联系手机：
固定电话：
企业邮箱：18117348636@163.com
联系地址：泗砖路600号
邮编：200000
联系我时，请说是在焊材网上看到的，谢谢！
INCOFLUXR 8 埋弧焊剂
INCOFLUX 8 埋弧焊剂设计与MONEL 67焊丝匹配使用，MONEL 67焊丝是一种含镍30％的高铜合金。这种焊剂的典型应用是MONEL 450（铜／镍比例为70／30）及其它一些铜镍合金的开坡口焊接。这种焊剂还可应用于碳钢的表面堆焊，但需要用Nickel 61或MONEL 60 填充金属作过渡层，防止由于铁的稀释作用使铜镍熔敷金属脆化。
|
焊接参数：开坡口焊或堆焊：应用DCEP电流方式和窄焊道 |
||||||
|
焊丝直径 |
电流／安培 |
电压／伏特 |
焊接速度 |
电极干伸长 |
焊剂层厚度 |
|
|
0.062 in 1.6 mm |
260-280 |
30-33 |
8-11 in/min 200-280mm/min |
7/8-1 in 22-25 mm |
1/2-1 in 13-25 mm |
|
|
0.093 in 2.4mm |
300-350 |
32-35 |
8-11 in/min 200-280mm/min |
7/8-1 in 22-25 mm |
3/4-5/4 in 19-32 mm |
|
|
电极摆动堆焊：应用DCEN电流方式，当焊丝直径为0.062 in时，摆动频率为50-70周／分；当焊丝直径为0.093 in时，摆动频率为35-60周／分 |
||||||
|
0.062 in 1.6 mm |
260-280 |
32-35 |
4 in/min 100mm/min |
7/8-1 in 22-25 mm |
1/2-1 in 13-25 mm |
|
|
0.093 in 2.4mm |
300-400 |
34-37 |
4 in/min 100mm/min |
7/8-1 in 22-25 mm |
3/4-5/4 in 19-32 mm |
|
储藏和干燥条件
焊剂密封在未开启的容器中可以无限期保存。如果焊剂暴露于潮湿环境中，可以在500oF保温烘干2小时或600oF保温烘干1小时后使用。
|
焊剂颗粒尺寸 泰勒制网目：10×100目
|
|
包装 桶盖上带有橡胶密封垫圈的60磅聚乙烯桶密封包装
|
The INCOFLUX 8 submerged arc welding agent is designed to match the MONEL 67 welding wire, which is a high copper alloy containing 30% nickel. The typical application of this flux is MONEL 450 (copper/nickel ratio 70/30) and some other copper nickel alloy open groove welding. This flux can also be applied to the surface surfacing of carbon steel, but it needs to be filled with Nickel 61 or MONEL 60 to prevent the metal embrittlement due to the dilution of iron.
Welding parameters: open groove welding or surfacing: apply DCEP current and narrow weld path
Electrode dry extension flux layer thickness of wire diameter current/ampere voltage/v welding speed electrode
0.062 in
1.6 mm 260-280 30-33 8-11 in/min
In 200-280 - mm/min 7/8-1
1/2-1 in 22 to 25 mm
13 to 25 mm
0.093 in
2.4mm 300-350 32-35 8-11 in/min
In 200-280 - mm/min 7/8-1
22-25 mm 3/4-5/4 in
19 to 32 mm
Electrode swing surfacing welding: the use of DCEN current mode, when the wire diameter is 0.062 in, the oscillation frequency is 50-70 weeks/min; When the wire diameter is 0.093 in, the oscillation frequency is 35-60 weeks/min
0.062 in
1.6 mm 260-280 32-35 4 in/min
100 mm/min in 7/8-1
1/2-1 in 22 to 25 mm
13 to 25 mm
0.093 in
2.4mm 300-400 34-37 4 in/min
100 mm/min in 7/8-1
22-25 mm 3/4-5/4 in
19 to 32 mm
Storage and drying conditions
The flux seals can be kept indefinitely in unopened containers. If the solder is exposed to wet conditions, it can be used after an hour of thermal insulation drying for 2 hours or 600oF.
Flux particle size
Taylor's mesh: 10 times 100
packaging
The barrel cover is covered with a 60 - pound polyethylene barrel sealed with rubber gasket
